Cannon Technologies Group
Products : Quick-Fit : Quick-Fit Fan Units

Quick-Fit Fan Units

Cannon's patented Quick-Change Fan Unit allows removal in seconds without the need to remove active equipment in top positions in the Cab and without the need to remove the Cab roof or overhead cable trays.

Quick-Change Roof Mounted Fan Unit 

Suitable for ServerSmart Cab and Smart Cab only.

 Cannon Quick-Change Roof Mounted Fan Unit

  • The Quick-Change Fan Unit allows fan unit to be omitted during initial installation for fitting later when and if heat loads warrant
    This simplifies project planning
  • The 3 pin IEC connection to the rear of the fan unit ensures an instant electrical break when fan is removed providing instant safety
  • No flying leads exist, avoiding danger of entanglement or shorting out
  • Deep server cabs need roof cooling fans to be further towards the rear of the cabinet for maximum efficiency, as fans too near front starve cooling air flow to front of servers. Cannon Quick-Change fan unit can instantly be fitted to rear of roof achieving this critical benefit
  • Front face of fan unit is set back (recessed) from roof edge. This provides protection for LED indicators and alarms when fitted
  • 2, 4 and 6 fan Quick-Change fan units available (230v 50Hz)

 

Finish: PaintedVelvet Black to RAL 9005 as standard.
Other colours are available on request.

 

Cannon Quick-Change Fan Unit - in situ

Order Codes

 

Number of Fans

Order Code

2

705E01510202

4

705E01510402

6

705E01510602

 

Quick-Change Roof Mounted Fan Unit - Low Noise

Suitable for ServerSmart Cab and Smart Cab only

 

General specification as the standard roof mounted fan (see below) but fitted with Low Noise Fans with a sound level of 0/27db (A) per fan.

 

Cannon Quick-Change Roof Mounted Fan Unit

  • The Quick-Change Fan Unit allows fan unit to be omitted during initial installation for fitting later when and if heat loads warrant
    This simplifies project planning 
  • The 3 pin IEC connection to the rear of the fan unit ensures an instant electrical break when fan is removed providing instant safety
  • No flying leads exist, avoiding danger of entanglement or shorting out
  • Deep server cabs need roof cooling fans to be further towards the rear of the cabinet for maximum efficiency, as fans too near front starve cooling air flow to front of servers. Cannon Quick-Change fan unit can instantly be fitted to rear of roof achieving this critical benefit
  • Front face of fan unit is set back (recessed) from roof edge. This provides protection for LED indicators and alarms when fitted
  • 2, 4 and 6 fan Quick-Change fan units available (230v 50Hz)


Finish:
Painted Velvet Black to RAL 9005 as standard.
Other colours are available on request.

 

Cannon Quick-Change Fan Unit - in situOrder Codes 

Number of Fans

Order Code

2

705E05650200

4

705E05650400

6

705E05650600

 

Horizontal Flow Fan UnitCannon Quick-Fit Horizontal Flow Fan Unit

The Cannon Quick-Fit 3U 19-inch Horizontal Air Flow Fan Unit can be assembled to the 19-inch equipment mounting posts in Cannon cabinets, or re-located to a new position, in seconds.
No more fiddly screws, cage nuts and washers, just two Cannon 1/8 turn Quick-Fit buttons.The unit is designed to assist in the horizontal movement of air where high thermal loads exist, such as in File Server applications.
Is held in place by two pre-formed hooks and two Quick-Fit buttons

Supplied: Complete with two Cannon Quick-Fit buttons and fitted with three axial 230V AC fans, finger guards and 2m lead with moulded 13 amp plug

Finish: Painted Velvet Black to RAL 9005 as standard
Other colours are available on request

Option 1

19-inch Mounted Fan Unit which exhausts warm air horizontally from the cabinet

  • 3 fan
  • 2m lead
  • 13A fuse moulded plug (230V AC option only)

Order Codes

Voltage

Order Code

230vAC

725E03600002

48vDC

725E03600006

-48vDC

725E05522303

Option 2

19-inch Mounted Fan Unit which inputs cool air horizontally into the cabinet

  • 3 fan
  • 230vAC
  • 2m lead
  • 13A fuse moulded plug

Order Codes

Voltage

Order Code

230vAC

725E03600003

Contact: +44 (0)1425 632600 | Email Cannon Technologies | Queensway, New Milton, Hampshire, BH25 5NU, UK accreditation

 


Contact the Cannon Sales Team today


Can't find what you are looking for?
Require a quote?


Contact the Cannon Sales Team

Guest.

Videos | Cabinet Configurator | Contact | Log On

Copyright © 2014 Cannon Technologies Ltd | Terms & Conditions | Privacy Policy | Cookies Policy | Site Map | Mobile Cannon Technologies Ltd on LinkedIn
Powered By Intergage | www.intergage.co.uk